Why You Need a 200 Amp Service Upgrade
Older homes were wired for far fewer electrical loads than we run today. Here is how to tell if your home is at its limit, what the upgrade involves in Massachusetts, and when it is worth doing.
If your home has 100 amp service, or an older 60 or 150 amp panel, it was probably sized for a different era: a few lights, a refrigerator, a stove and a TV. Today the same house may need to run central air or a heat pump, an induction range, an EV charger, a home office, and a finished basement. A 200 amp service upgrade gives the whole house more capacity so those loads can run safely together.
We are a family-owned remodeling company with more than 20 years of experience, and we see this question come up in Weston, Wayland, Sudbury, Waltham and the surrounding towns almost every time a homeowner plans a kitchen, basement, addition or heat pump project. This guide explains what to look for and what to expect.

What does 200 amp service actually mean?
“Amps” describe how much electrical current your home can draw at once. Your service size is set by the equipment where power enters the house: the service wires from the utility, the meter socket, and the main breaker in your panel. A 200 amp service can supply twice the capacity of a 100 amp service.
It is not the same as just changing the panel. A larger panel on undersized service wires or an old meter socket does not give you more usable capacity. A true service upgrade replaces the parts that limit the system, which is why the work is usually done by a licensed electrician and inspected by the town.

| Service size | Where we usually see it |
|---|---|
| 60 amp | Very old homes that have not been updated. It is often not enough for modern living. |
| 100 amp | Many homes built before the 1990s. It can be fine for a smaller home with gas heat and few big electric loads. |
| 150 amp | Some mid-size homes and earlier upgrades. It may leave little room to add large loads. |
| 200 amp | The common standard for newer construction and renovated homes. |
Signs your home may need a 200 amp upgrade
- Breakers trip when you run several appliances together
- Lights dim when the dryer, oven or AC starts
- Your panel is full and every new circuit needs a workaround
- Doubled-up (tandem) breakers or extension cords used as permanent wiring
- Your panel is an older brand or is warm, buzzing or rusted
- You are planning a heat pump, EV charger, induction range or hot tub
- You are finishing a basement or building an addition
- Your insurer or home inspector flagged the panel
Safety: Warm or discolored panels, a burning smell, buzzing, or breakers that will not stay reset are warning signs. Do not open the panel yourself. Call a licensed electrician right away.
Why a 200 amp upgrade makes sense
1. Heat pumps and electric heating
Cold-climate heat pumps are one of the best ways to cut heating costs and add air conditioning, but they add a real electrical load. Some homes with 100 amp service can add one after an electrician runs a load calculation, and some cannot. If you are planning to replace oil or gas heat, it is worth finding out early whether your service can handle it. We cover this on our heat pump installation page.
2. EV chargers
A Level 2 home charger commonly needs a dedicated 40 to 50 amp circuit. On a smaller service that can push the home past its capacity, especially when the dryer and oven are running too.
3. Kitchen remodels
A new kitchen often adds an induction or electric range, a wall oven, a dishwasher, a microwave drawer, more outlets and lighting. If you are planning one, we look at your panel before the design is final. See our kitchen remodeling page for how we approach it.
4. Basements and additions
Finishing a basement or adding a room means new lighting, outlets, heating and cooling. A finished basement or a home addition is often the point where an old panel runs out of room.
5. Safety and insurance
Overloaded circuits and outdated equipment are a leading cause of electrical problems in older homes. A new panel with modern breakers, proper grounding and arc-fault and ground-fault protection where required gives you a safer system. Some insurers also ask questions about older panels, so a modern panel can make coverage easier.
6. Room to grow, and resale
Even if you do not need it today, upgrading while walls are already open for a remodel is usually cheaper than doing it separately later. Buyers and inspectors also look at the panel, and 200 amp service is what most people expect in a modern home.
How a service upgrade works in Massachusetts
The exact steps depend on your town and your utility, but the process usually looks like this:
- Site visit and load calculation. A licensed electrician looks at your panel, meter and service wires and calculates how much capacity your home really needs.
- Permit. In Massachusetts an electrical service upgrade requires a permit from your town, which the licensed electrician pulls. Fees vary by town.
- Utility coordination. Your utility (Eversource, National Grid, or a municipal light department) must be involved when the service size changes. Depending on the utility and the home, that can mean submitting an application, scheduling a disconnect and reconnect, and sometimes setting a new meter.
- Installation. The electrician installs the new 200 amp panel, main breaker, meter socket and service wires as needed, and improves grounding if required. Power is typically off for part of the day, so plan for that.
- Inspection and reconnect. The town’s wiring inspector approves the work, and the utility restores power.

The work itself often takes about a day, but permits, utility scheduling and inspections mean the whole project can take a few weeks from start to finish. Plan ahead, especially if the upgrade is part of a remodel or a heat pump install.
What does a 200 amp upgrade cost?
Prices vary a lot. A simple panel replacement is usually less expensive than a full service upgrade that also replaces the meter socket and service wires, and costs go up if the utility needs to do additional work, the panel location has to move, or the walls need repair. Published estimates for Massachusetts commonly run from a few thousand dollars on the low end to around $8,000 or more for larger jobs, and your town’s permit fee is on top of that.
We do not like giving a number without seeing the house. We look at the panel, the meter, the service entrance and your plans, then give you a written, itemized estimate. If we find something unexpected during the work, such as hidden wiring problems, we explain it and get your written approval before any added work. If you want to spread the cost, we also share information on financing options.
Tip: If you are adding a heat pump, check whether Mass Save has rebates or financing that apply to your project. Programs and amounts change, and some require a participating installer, so check the current rules first. Utility and state programs may also have incentives for electrical work tied to electrification, depending on your income and project.
Do you really need 200 amps?
Not every home does. A smaller home with gas heating, gas cooking and no plans for big electric loads can run fine on 100 amp service. The right answer comes from a load calculation, not a rule of thumb. If your electrician finds your existing service is adequate, you save the money. If not, you will know exactly why.
A good rule: if you are about to spend money on a remodel, a heat pump or an EV charger, have your service checked first. It is much easier to plan for the panel than to discover the problem halfway through.
Frequently asked questions
Not always. The panel is one part. The service size also depends on the service wires, the meter socket and the main breaker. A full upgrade replaces whatever limits the system.
Yes. In Massachusetts a service upgrade needs an electrical permit and an inspection, and a licensed electrician must do the work. Be cautious of anyone who offers to skip the permit.
Usually for part of one day while the old panel is replaced and the utility reconnects service. Your electrician will confirm the plan with you beforehand.
No. It raises capacity, not usage, so you pay for the electricity you use, not the size of the service. The benefit is safety, reliability and the ability to add things like a heat pump or EV charger.
Sometimes. It depends on what else the house already uses and the size of the heat pump. An electrician can run a load calculation to tell you for sure.
Not sure if your panel is up to it?
Triforce Remodeling is a family-owned and operated remodeling company. We will look at your electrical service and tell you honestly whether an upgrade makes sense. Schedule a free in-home consultation or call (781) 790-4377.